puts out 402 flywheel horsepower. at 20 psi
it is capable of 28 on this engine and tranny.
- JDM engine 40k (mobil 1 full synthetic)
- (ported head, GRODEN BILLET ALUMINUM RACING RODS, JE pistons)
- JDM tranny 40k, (bg synchro shift.) (short throw shifter)
- HKS head gasket
- ARP head studs
- safc/avcr
- 2g MAF
- aluminum intake Tube.
- DSM pocketlogger
- mutt ete52 550bhp .60 trim
- braided oil lines
- 3 inch exhaust
- Apexi N1 Muffler
- race Cat
- o2 eliminator, not installed
- egt/boost guage
- kyb agx
- oz f1 rims
- 28x10.5x3 in DSR FMIC (36 inches total width)
- 2.5 inch ic piping with all hardware.
- 2.5 inch TB elbow
- 660 injectors
- 255 walbro
- 8 guage fuel pump hardwire.
- 2 slim line high flow fans (always on)
- 180 degree thermostat.
- hks sqv and many more mods, extra OEM gaskets and parts.
- sbc-d, blitz turbo timer
the head has just been reworked (milled, new valves, lifters, Gaskets...etc. hot tanked)
seats/paint/int are like new very low mileage, all new stuff.
email me for pictures and more info. 15k invested.
the car dynoed approx 323.1 whp at 19.5 psi, it is capable of 28 psi on this engine and will put down approx 440 whp at that psi. i have receipts on almost all work.
latest track time was 11.7 at 122. has gone 11.4 at 127.
i have the 11.7 slip.
8,000 OBO.
http://www.elit3.com/talon/talon.htm
it is capable of 28 on this engine and tranny.
- JDM engine 40k (mobil 1 full synthetic)
- (ported head, GRODEN BILLET ALUMINUM RACING RODS, JE pistons)
- JDM tranny 40k, (bg synchro shift.) (short throw shifter)
- HKS head gasket
- ARP head studs
- safc/avcr
- 2g MAF
- aluminum intake Tube.
- DSM pocketlogger
- mutt ete52 550bhp .60 trim
- braided oil lines
- 3 inch exhaust
- Apexi N1 Muffler
- race Cat
- o2 eliminator, not installed
- egt/boost guage
- kyb agx
- oz f1 rims
- 28x10.5x3 in DSR FMIC (36 inches total width)
- 2.5 inch ic piping with all hardware.
- 2.5 inch TB elbow
- 660 injectors
- 255 walbro
- 8 guage fuel pump hardwire.
- 2 slim line high flow fans (always on)
- 180 degree thermostat.
- hks sqv and many more mods, extra OEM gaskets and parts.
- sbc-d, blitz turbo timer
the head has just been reworked (milled, new valves, lifters, Gaskets...etc. hot tanked)
seats/paint/int are like new very low mileage, all new stuff.
email me for pictures and more info. 15k invested.
the car dynoed approx 323.1 whp at 19.5 psi, it is capable of 28 psi on this engine and will put down approx 440 whp at that psi. i have receipts on almost all work.
latest track time was 11.7 at 122. has gone 11.4 at 127.
i have the 11.7 slip.
8,000 OBO.
http://www.elit3.com/talon/talon.htm
