Ford Mustang Forums banner
1 - 20 of 1555 Posts

·
Registered
Joined
·
2,672 Posts
Discussion Starter · #1 · (Edited)
We here at corral are a very community based mustang website. We have connections here that blow my mind. At any rate. It has come to my attention that we have the means to run a limited, maybe new line, of 1993 cobra rims that are 5-LUG!!!!!!

The requirements are the following:
1. We have to secure an order of 20 sets of rims, to make this first run. (I am not naming names as to who where etc., but it can and will be done. I have taken it upon myself, to poll the sales and to try to complete this group order.)
2. Please reply to this ad and in your post, number your self accordingly so that our member can see how many sets we have to go to get the ball rolling.
3. On a poll of 20 or more sets we will majority rule the dimensions to the winners.



Our limited run will resemble 93fiveoh's prototype rims.
THANKS FOR THE PICS 93FIVEOH!!
 

·
Registered
Joined
·
1,799 Posts
#1 for what ever is neccesary for:
a stock track rear, and 94-95 front spindle. I would love to see 17x8 and 17x10!
 

·
Registered
Joined
·
1,799 Posts
Wheels will still be 17x8.5

The only things that can be changed are offset, centerbore and bolt pattern by changing the centermold

maybe the poll should be set up at the top and be up for a vote so that the stats are shown

I am sure the only options we will need are fox stock track, sn95 rear width track, and the oem cobra width track...
 

·
Registered
Joined
·
290 Posts
#1
17x8.5" wheel with a +26mm offset, and 5.72" backpacing.
OR
17x8.5" wheel with a +26mm offset, and 5.5" backpacing. This way I can have them widened to 9" and still have room for a 255.
The BS doesn't change with the same offset unless you change the width of the wheel. Remember the offset is from the center of the wheel, which +26mm would mean the hub face is 26mm to the outside of the wheel if I remember right. I believe + numbers are toward the front/outside and - number are to the back/inside, someone please correct me if I'm wrong.
 

·
Registered
Joined
·
290 Posts
Wheels will still be 17x8.5

The only things that can be changed are offset, centerbore and bolt pattern by changing the centermold

maybe the poll should be set up at the top and be up for a vote so that the stats are shown

I am sure the only options we will need are fox stock track, sn95 rear width track, and the oem cobra width track...

The wheel track is the same between the SN95, Cobra, and T-Bird if I'm not mistaken, which is 3/4" per side wider than the Fox track.
 

·
Registered
1995 Cobra
Joined
·
598 Posts
17x8.5 +26mm offset, 5.74" backspacing. I really only need 2 of them, but if necessary I would buy a set of 4. Here's my question to you....are these going to be painted? The run of 20 you get will all have to be the same finish correct? I prefer the painted as pictured.
 

·
Registered
1995 Cobra
Joined
·
598 Posts
One more, did you post this over on SVTperformance for the guys over there in the fox cobra forum?
 

·
Registered
Joined
·
1,171 Posts
id buy a set, but what would be the best measurements for a fox with 94/95 spindles, cobra brakes all around, & fox length axles with nrc brackets?
 

·
Registered
Joined
·
46 Posts
heh. i came FROM fanblades on my tbird lx... i dont want them again unless tehy are 17's.. and 5 x 4.25... any chance they could be drilled that way? might check over on tccoa.com, or sccoa.com for interest too.
 
1 - 20 of 1555 Posts
Top