Ford Mustang Forums banner
turbo
1-20 of 311 Results
Advanced
  1. 94/95 Tech
    Just bought the second gen on3 turbo kit for 94-95 mustang. Was wondering if anyone also bought it and had any info on it like tips or tricks from stuff they ran into?
  2. Turbochargers
    Hey Im lookin for a turbo for my stock 85 5.0, its currently in my back yard and im getting new tires for it but it will be my daily driver it has under 90k miles on it and im not trying to spend more than 1300 on the turbo. I want a good turbo but im not really sure what im lookin for since im...
  3. Power Adders For Sale
    I am parting out my turbo windsor to do a coyote swap and no longer need the turbo. It is a Precision 7675CEA with the ceramic bearing upgrade. Precision CEA technology is based on a compressor wheel machined from a 2618 aluminum forging and offers higher efficiency and faster spool times...
  4. Fuel System & Related
    Selling my 3" PMAS blow through MAF sensor. Only has a few hundred miles of use. Went to full stand alone and speed density so don't need anymore. Has adapter connector for Fox Body style MAF, uses the newer style Ford MAF sensor with integrated IAT sensor that can be wired up for charge air...
  5. Mustangs For Sale/Wanted, 1999-2004
    Msg for videos of car running and oil pressure For Sale: Turbo 2003 Built Motor & Rear Mach 1 570/523 @ 14psi, turbo could be turned into 20's with more tuning Car is Black in color, wrapped in 3M gloss wicked Accident on Title*** 76k miles on car, ~3k on all modifications Title in hand $9,000...
  6. Power Adders For Sale
    Forced Inductions billet s400 76mm ETR turbocharger with their 93mm turbine wheel in a T4 1.10 AR housing. V1 race cover. Turbine housing is ceramic coated black. 1 season old, no shaft play, smoke, knicks in the wheels, etc. Went deep mid 8s at over 900rwhp with this unit in a 4.6 2v Mustang...
  7. SVT & DOHC
    I have a 02!gt with a 98 cobra motor and single turbo. The other day I noticed it was only make 6-7 psi when it normally makes 10-11 psi. Next day I checked for boost leaks (hooked my compressor to the turbo inlet with about 18 psi sprayed with soap water). I found a couple small ones nothing...
  8. Mustangs For Sale/Wanted, 1999-2004
    I’m finally willing to separate from my baby. I am not interested in trades I’m looking only for cash. Want the money for down payment on land. Up for sale is my 2000 mustang 4.6 with a t-56 fully built motor and turbonetics 78mm turbo. I have had this car for about 11 years. Here is a quick run...
  9. 5.0/5.8 Engine Tech
    Hey guys/gals, I'm going to crowdsource the next upgrade on my 92 notch. I've never been in these power levels before, so I'm starting to feel a bit lost in terms of supporting mods with my turbo. Here's a list of my current mods, so feel free to recommend what you think I should do next (what...
  10. General Mustang Tech
    Currently in the middle of installing the On3 turbo for my notch. It's a 68mm that we're going to keep around 6-10 pounds of boost. I was all set to close the PCV valve on the intake and run a breather on the oil tube, but after looking a bit deeper, some have told me I need to have more of an...
  11. 94/95 Tech
    New member just pick up another mustang to collection and new to form ? Is got. 95 mustang gt turbo car with mega squirt 2 car idle fine and cruise great but when u Let off the throttle comeing to a stop car will shut off unless u tap gas couple times any advice on where to start would be great...
  12. Turbochargers
    I searched through the forums and couldn't find a post that really answered all my needs so hopefully this doesn't break any rules and sorry if I do but I am in highschool and I'm new to building cars. I am getting started to build a 331 stroker turbo build that's mainly a street car but I will...
  13. Turbochargers
    I'm giving serious consideration to one of these kits for my mostly street weekend driver notch. Mild build so far: GT-40 heads, Exploder intake, 24lb inj., yada, yada. Looking to make 450-550 rwhp. I'd like to retain the A/C and front sway bar too. What's your experiences and impressions with...
  14. Turbochargers
    I am working on timing tables on Holley EFI for my 93 octane running turbo 363. It has higher compression than the usual power adder cars but definitely not the first. RHS 210 pro series heads, FTI turbo cam, victor Jr. intake. Running 3922XP plugs. running 93/112 mix but want to get it on 93...
  15. Power Adders For Sale
    For Sale: Pair of Master Power turbine housings P-trim .68 A/R T4 undivided inlet 3" v-band outlet $200 Location: Indiana, 46711 email: adynes(at)gmail
  16. Turbochargers
    Hey everyone I am new to this forum and I have been debating on what route I should go with for my engine build. I have a 2003 Ford Mustang GT. Background: I have been having exhaust smoke issues, come to find out I have low compression in cylinder 4. I had dripped some oil down only to find...
  17. Power Adders For Sale
    F/S: B&G Foxbody Turbo Kit with Precision Turbo Sold! I am selling a B&G Turbo kit that came off of my 1987 Mustang GT. The turbo kit has about 8,000 miles on it. The turbo itself is like new and has less than 1,500 miles on it. -B&G Custom Turbo Kit HOTSIDE: - 1 5/8 Mild Steel...
  18. SVT & DOHC
    Purchased a 2003 Mach 1 from a guy off Facebook with a locked up engine. I got it with the intention of building an engine for it and adding a 76 turbo to it. This will be my first all out build. However I am not looking to build an all out drag car just a quick street car shooting for 700+. I...
1-20 of 311 Results
Top