Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 53 Results
  1. General Mustang Tech
    Hi! I was replacing my thermostat and housing and one of the bolts was stuck real bad so I took the lower manifold out and had it machined. Then I reinstalled everything and now it won't start. When I took the distributor out I didn't make sure it was at TDC so I'm pretty sure the timing is way...
  2. 5.0/5.8 Engine Tech
    Hello I am reposting this. My tfi wend out replaced tfi and coil. Ran but did not run right. Replaced distributor runs good but timing does not advance. Checked the continuity of spout. It to the ecu and to tfi. All good. Timing advances once plugged it from 12 to 14 but does not advance as rpm...
  3. 5.0/5.8 Engine Tech
    Hello I have a 1991 mustang 5.0 and it died while at a stoplight. It was not starting and I did not have constant spark it would just have spark turn on then die a second. Some times I would not have spark at all. I changed the coil and tfi module and now it starts and idles fine. However it...
  4. 94/95 Tech
    Ok so for starters I have a 95 mustang cobra with a on3 turbo kit. For a while now the car has basically been undrivable at speeds due to timing being retarded starting from about 1800 rpm and progressively getting worse till around 4krpm. This issue is still present whether the spout connector...
  5. GT & SOHC
    Hello, I am in the middle of doing an engine swap on my 2000 mustang gt. Both engines are a 4.6, the new one being out of an 04 explorer. Everything was going good up until I went to put on the harmonic balancer. Tried each balancer from each engine but neither would seat properly, with about a...
  6. 5.0/5.8 Engine Tech
    So now I think only 1 problem to fix before I can put the car on road. This is what I’m facing now. I recently changed my intake and had to take the dis out. Now I can’t seem to figure it out. My balancer doesn’t have timing written on it. So when I did try to put the dis back in after finding...
  7. GT & SOHC
    I bought a bare block used. I have installed the heads, oil pump and now I have moved on to installing the timing components. I bought the Cloyes kit from RockAuto and the drivers side installed fine. The passenger side is where the issue is. I have a roll pin in the place a bolt should be. I...
  8. 5.0/5.8 Engine Tech
    Hi everyone, I’m new here so if I’m formatting my post wrong or anything just let me know. Recently I picked up my first ever project car, a 1983 GLX with a 5.0 HO. I had to fix an oil leak between the intake and the block so I had to pull the distributor to change the gasket. When I did that I...
  9. 94/95 Tech
    Hey guys, recently just put promaxx heads, an e303 cam, new timing chain, new lifters, hardened pushrods, and Lunati rockers 1.6 ratio. Been doing my own mechanical work for 20 years now. No, I'm not certified, but know how to do almost anything to a pushrods mustang including screw it up...
  10. Turbochargers
    I am working on timing tables on Holley EFI for my 93 octane running turbo 363. It has higher compression than the usual power adder cars but definitely not the first. RHS 210 pro series heads, FTI turbo cam, victor Jr. intake. Running 3922XP plugs. running 93/112 mix but want to get it on 93...
  11. Modular Engine Parts
    04 cobra timing cover with crank/cam sensors and tensioner $200
  12. Modular Engine Parts
    $75 $85 shipped CONUS, 30269 Buyer pays all Paypal costs.
  13. SVT & DOHC
    I have a 5.4 DOHC from a 2002 Lincoln Navigator. I removed the oil pan and found two plastic clips. After removing the timing chain cover and examining the guides they looked in better shape than the plasctic pieces that I found. I think I found the location they go but Im not sure if Im...
  14. 5.0/5.8 Engine Tech
    I have a 91 lx with b303 alum gt40s 1.7rr explorer intake. Im experiencing some pretty substantial low rpm bucking and was wondering, other than timing what can i do to improve this? Do the bcam and 2.73s not mix? Any help is appreciated.
  15. GT & SOHC
    So, I built a 5.4 and swapped it into my 2000 GT and it has a rattle that 3 shops so far can't diagnose. It's a strange one, seems to be coming from passenger side, is notable on cold start then when warmed up you can only hear it when the windows are up and everything is off , luckily it's not...
  16. Windsor Engine Parts
    This unit drops in place of the distributor and provides a crank and cam reference signal when used with a stand alone, or any capable engine management system. Brand new. Looking for $275 shipped. Paypal preferred. chadsparts@gmail.com
  17. Modular Engine Parts
    I have myself a dilemma here. I bought 99 cobra cams and didn't get any secondary sprockets with them. I need the sprockets with the keys so that I can correctly time my engine. Please, help me out!
  18. Electronics and Entertainment
    I have this for sale.. MSD Boost Timing Master ( Vortech Mustang Supercharger ) MSD Boost Timing Master with the 5.0 jumper harness. $140 shipped to the lower 48 states!
  19. GT & SOHC
    ok guys, my 96 has an issue... its been pinging alot lately, but always has if i didnt run premuim. well tuesday after noon, i drove to dr about an hour away, all kinds of speed, normal 70mph interstate driving. well, went to leave, car crunk fine then immediately stalled. i was suprised bc this...
1-19 of 53 Results
Top