Ford Mustang Forums banner
swap
1-20 of 113 Results
Advanced
  1. GT & SOHC
    I currently have a 2003 Gt with a rod knock and I was wondering if an engine out of a 2008 mountaineer would be a suitable replacement. I got the motor for cheap and I know that id have to replace the top end stuff but would I be able to make it work?
  2. Mustangs For Sale/Wanted, 1999-2004
    Im looking to sell my 1999 GT with a 98 Cobra swap in it with a clean title. Has 240k miles on the body and the engine only has 80k miles. Has the following parts done: Long tube headers JLT CAI BBK 72mm Throttle Body Under Drive Pullies 4.10 Gears Short Shifter SCT tuner EGR Delete Catless...
  3. GT & SOHC
    Hello, I'm new to the forums and currently in search for more information on swapping a 03 crown vic motor in my 97 standard mustang gt. I have most of the parts ready to go for the swap but does anyone know if everything will work if I can get the motors engine harness? I know it's COP vs the...
  4. Powerplant
    Im in the middle of a 4v swap into my 99 GT and now im running into an issue. Im trying to reinstall the new engine back in with long tube headers on it and the engine is not wanting to go back in. It looks like the header on passenger side is rubbing against the side if the engine bay and...
  5. General Mustang Tech
    I swapped 2.3 to 5.0 Foxbody and did everything by the book. When I start it it runs at 1600 rpms. I messed with the tps and it all checks out. Vacuum lines are all in the right spots without leaks. Any suggestions are appreciated. This is the last thing I need to do and it’s taking me longer to...
  6. 5.0/5.8 Engine Tech
    Hey guys i have a 1996 351w and i want to know if i can do a 393 without boring it? To make like a 387? If yes, I bought dms-8723-4000 forged piston for 302 with 1.605 pin height. What i need to do to my block? : 1996 351w Can i only put a 3.85 stroke crank in it with New bearing and New rod...
  7. Exhaust Parts
    Dynatech LS Swap headers for a foxbody, will fit perfectly with a UPR or AJE K-Member. I have welded on V-Bands to make for easy exhaust removal. I am also selling my X-Pipe that has V-Bands welded as well. Fit perfectly on my 1987 Foxbody, will fit any LS fox from 1979-1993. Dynatech 1 7/8...
  8. General Mustang Tech
    I have an 88 mustang gt 5.0 and i removed the stock t5 transmission since it blew apart. I installed a tremec 3550 5 speed transmission and I’m looking for the correct speedo gear to install. The car has 4:10 gears and i went off LMR’s website calculator and its still way off with the gear i...
  9. Modular Engine Parts
    Brand new, never out of the package(s), Ron Francis' "The Detail Zone" offers this Telorvek Ford 4.6/5.4 V8 Modular EFI Wiring Harness, part number MK97A. This is the swap harness you'd need to take your complete 4.6/5.4 engine/transmission combo' (including the supercharged Terminator and...
  10. 5.0/5.8 Engine Tech
    Hi Corral, I am looking to build a bang for buck windsor to replace my tired 302 in my 94 cobra. Not looking for a track car, just a really fast daily. Affording machining, rotating assemblies, and aluminum heads for a windsor stroker seemed a bit steep. The clevor had come up as a viable...
  11. Drivetrain Parts
    I've got a 98 GT with ~150k miles that has a stock automatic 4R70W. Curious if there's anyone out there that would rather have an auto instead of their T-45? I understand that it's high-ish miles and stock, I wouldn't be asking for a T-45 out of a mint 20k mile car. I would love to go manual...
  12. 5.0/5.8 Engine Tech
    Hi, I'm looking to swap a rebuilt 01 mountaineer 5.0L into my 94 Cobra. My current motor uses a distributor for ignition and the mountaineer motor I'm looking to put in uses coil packs. The 01 Mountaineer/Explorer motors had GT40P heads and GT40 upper and lower intakes if that helps at all. I am...
  13. General Mustang Tech
    Hey, Newbie here so go easy. I have a 1998 mustang gt runs great......but its automatic :[ I want to do the manual conversion but very unsure on exactly what I will need and know this is a big and expensive job. Heres what I got so far: T-45 Transmission itself Flywheel Clutch,pressure plate...
  14. SVT & DOHC
    I'm not much for write ups, I'm posting up what I have done so far with a pile of pictures for anyone who may have an interest. ENJOY. This is for anyone who cares to see how I chose to swap the Navigator 5.4 DOHC into my 2000 v6 convertible. Started as a plain 3.8 automatic 2000 Mustang...
  15. Modular Engine Parts
    2008 complete 4.6 3v engine for sale. 40k miles only!!!! my reason selling is for a bigger swap. Ran perfect when pulled. Everything included from intake to oil pan! Harness, starter, fuel pump, k member also included. I'm forgetting a few things too I'll have to double Check what else comes...
  16. 351C/BBF Parts
    Canton BBF Foxbody 15-770 conversion 429-460 oil pan, 15-771 pickup tube, and 20-850 dipstick. Used but in great shape. Paid over $400 for everything. $300 Shipped to the lower 48.
  17. S197 Mustang GT (2011-2014)
    Hello Corral, Not sure if I'm in the right section but thought I'd start here since its all about the coyote motor. I have a F150 coyote swapped notch. The motor is completely stock and I want to throw a whipple on it. My goal is a 600hp street car and I was wondering if someone has done it...
  18. Drivetrain Parts
    New. $45 shipped from 30269. Pix: https://drive.google.com/folderview?id=0B6NlbZzWOkJiQVB5M2I0ZS1nVXc&usp=sharing
  19. Fuel System & Related
    im wanting to run dual fuel pumps using an 03 style tank in my 97 Cobra. Im just not sure which one to get. i know the middle one says its for a 97 but it has less holes in it and the other two are more similar to the stock tank. to anyone thats done this swap which tank did you use. TIA Doug...
1-20 of 113 Results
Top