I have a 92 tbird 5.0 (same as 94-95 fox) and I am making a custom intake to adapt a M112 and need some help/info with injectors.
I am planning on making in the range of 400-500FWHP and im not sure what size injectors to get.
I will need to weld in bungs in my intake so the kind of injector...
Hey I am sure this has been asked before but I can’t find the answers I’m looking for. I’m relatively new to these foxbodys and I have a question for making some easier power. I have an explorer motor in my notch with the p heads and a mild cam. I am looking to upgrade to a nice supercharger...
4.6L SOHC V8
Vortech supercharger with aftercooler
Dyno tuned making 413 rwhp / 407 tq with a safe tune on 91 octane
5-speed manual transmission
Car is blue with grey leather interior. Just turned 72k miles. Clean and clear title. Carfax report in hand. Overall good condition and is ready to...
This SUPERCHARGED 2005 Mustang GT is in AMAZING condition. Asking $14,750 and is located in Oak Harbor, WA.
The Mustang has a Paxton Novi 2200 supercharger with intercooler and has been Dyno tuned and recorded 445 RWHP and 410 ft lbs of torque. It has been upgraded with high-capacity fuel...
1995 Ford Mustang GT
Tune by Lidio at Alternative Auto
Stock bottom end
Vortech V2 Si Supercharger on 13lbs of boost
90mm Mass Air Anderson Power Pipe
75mm BBK Throttle body
TFS Street Heat Intake
Pro Topline/RHS 180cc Heads - Inspected by Holbrook...
Selling my 2004 Ford Mustang SVT Cobra with 104K miles. Exterior color - Redfire, Interior color - Dark charcoal/Dark charcoal
This car is 13 years old. It is not perfect but its extremely solid. There is a random rust hole in the very center of the passenger door. It's about the size of a...
For sale is my:
5-speed Manual Transmission
+500 Horsepower Mustang GT
It was dyno tuned to 498 rear wheel horsepower by JDM Engineering. With drivetrain losses (typically +12.5%) that is north of 570 flywheel horsepower. (Dyno sheet...
I want to sell my intercooler kit that I bought a month ago from CX racing, no cutting is needed, you can also keep your Bumper Support, will fit perfectly with Mounting Brackets. Its a complete kit that includes:
Intercooler + Oil Cooler + Bracket + Piping + Silicon Hose + Clamp +...
Looking to purchase clean well built 85-93 notchback. Must be either aftermarket block, Windsor stroker or LS powered. Prefer turbo or Vortech T trim YSI etc. Want 600-700 rwhp Prefer fuel injected but may consider blow thru setup. Exterior and interior need to be excellent to show quality...
Used 2008 Ford Mustang GT
Drive Type:2 wheel drive - rear
All the front converted from a GT to Cobra, using all original Ford Dealer parts.
2004 F1A Mach1 560whp
azure blue, 40th anv edition, 5 speed, F1A procharged, low compression aluminator crate motor, full exhaust, twin 03 cobra pump setup plus boost a pump, red procharger race bov, 80lb injectors and more, made 560whp 480tqe on low timing very safe tune by Bill M. at pro edge...
You are looking at a fully custom 1993 Ford Mustang Cobra. This is a true Cobra. It has the factory 302 block, bored 30 over so it's a 306. windage tray, studded block, stud girdle and 7qt oil pan. The body has just under 140k on it, but the engine, transmission, suspension, front end, and rear...
What are pros/ cons of putting an larger throttle body (75-80mm) on my 98 4.6L DOHC?
Mods: ProCharger PSC-1 (full system installed; fuel pump, management system, etc..) ; Borla exhaust, header - back
Stock everything else. Bought as it currently sits and a dyno sheet of 390 RWHP. It is very...
'99 Roush Triple Black Vert Vortech V3 $11,000
Posting up my '99 Roush Stage 1 for sale. Pulls very hard with 417hp to the wheels, but drives very nice also. No surging, no idle issues, no CEL, no nothing.
4.6L V8 2v
Black interior, black exterior, black top
Not sure if I'm in the right section but thought I'd start here since its all about the coyote motor.
I have a F150 coyote swapped notch. The motor is completely stock and I want to throw a whipple on it. My goal is a 600hp street car and I was wondering if someone has done it...
Hey guys.. First post, I know, I know.. For whatever reason, when I was heavy into Mustangs I never found this site. Was on several others, but.. In any event, a buddy suggested I list this on here, so here goes.
2006 GT Premium Convertible
Black on black on...
I am selling my hardly used (1500 miles conservative estimate) Dart Iron Eagle 331 with Trick Flow 206 Race cnc heads. All ARP bolts and studs from the rockers arms down to the oil pan. Crane Gold Race 1.6 3/8 arp stud mount, Bennett Racing custom blower cam, JE 4340 forged 9.5:1 pistons, Eagle...