Search Results for ‘mustang’

I swapped 2.3 to 5.0 Foxbody and did everything by the book. When I start it it runs at 1600 rpms. I messed with the tps and it all checks out. Vacuum lines are all in the right spots without leaks. Any suggestions are appreciated. This is the last thing I need to do and it’s taking me longer to...

Used Nitrous Outlet hard line kit for 2011-2018 Mustang / F150 with 5.0. Kit has the optional purge and nitrous bottle pressure gauge as well as the billet bottle bracket purchased separately. Works perfectly. Sold with bottle empty. Nearly $1,500 new. Selling for $900 OBO. Switching car to...

I have a 92' notchback with 30k miles on body. The car makes 1150 RW on 12 pounds. I am interested in selling the car. The asking price is 50k OBO, but am open to trades. Trades include a built Corvette z06, 69' Camaro, or 70' Chevelle SS. Serious inquiries ONLY. If interested, you can contact...

Complete 1997 Ford Explorer for sale. 302 V8 (Liter) EFI engine runs great. This is a prime engine used in Mustang restomods. AOD transmission and rear axle also favorites for Mustang projects. Transmission is slipping and needs rebuild. Goodyear tires have 5,000 miles on them. Rest of...

306 SBF 10:1 Comp Pumpgas Motor Eagle Crank And Rods Bullet Cam Edelbrock Ported Heads Harland Sharpe Rockers Victor Jr Intake [email protected] on Alky 10.90 On Pumpgas 50 Runs Since Freshened By Riegel Race Engines Very Consistent Bracket Motor.Late Rounds In Big $$$ Footbrake Races Every Showing...

So I've decided to go with a 302/t5 setup. I need everyone's opinion as I will be doing all the work myself. Beginning as a 2.3/A4LD what all will I need to do? I know I have to change the rear-end to a 8.8 and up. I know If I go with carb setup I will have to go with a low pressure fuel pump...

I bought a bare block used. I have installed the heads, oil pump and now I have moved on to installing the timing components. I bought the Cloyes kit from RockAuto and the drivers side installed fine. The passenger side is where the issue is. I have a roll pin in the place a bolt should be. I...

Hello there. 2005 Ford Mustang S197 is my car. I`m Glad to joined your site and would like to introduce myself. My name is Robert and I am a proud owner of a Mustang. Thanks for having me.

Had battery disconnected while I worked on it for a couple of weeks. When I turn key, I hear the fuel pump prime; and when key is in 'ON' position, NO theft light. However it behaves exactly like a PATS issue. It starts and immediately shuts off. Any ideas? Thanks

Hey guys , New user here so bare with me . So I have a 90 mustang that is charged with a vortech v2 with 10 rib pulley . Has a b303 cam, 340lph fuel pump woth a regulator . And 60 lbs injectors . Have a sct chip not yet tuned and a maf sensor not installed yet . Anyway im dropping the motor in...

Hello, im new here and trying to get my 86 gt running with no problems. Currently it overheats and also stalls randomly (I think it might be the TFI module). Anyways I’ve already changed the thermostat, pulley belt, some radiator hoses, and radiator cap but no solution. I think I might’ve...

aquiring parts to start building my 89 302 up future plans for the car are to run an on3 76mm turbo kit, I have a set of TFS 192 highport heads, trick flow port matched upper and lower intake, 1.6 RR's however im stuck deciding between a cam, maximum valve lift on the heads are .600, does that...

Welp, the time has come to finally put together my build thread. Im not generally someone who is great at documenting my work or taking before/after pics of my progress. I kind of get tunnel vision while working on the car and just go for it until Im too exhausted to go further. With that...

Hey guys new to the forums here looking to get myself into a coyote..guy selling on marketplace has a 2011 mustang gt with 206000 miles on it for 8900 figured I could talk him down to 8500 atleast..it is about a 2hr drive as well for me.. the guy says he bought it new and has stayed up on all...

Looking to sell my baby. Its a 97 Cobra with 74,000 original miles. At 70,000 miles i did a swap from an 04 cobra that included a built teksid block, C heads, and a 2.6 Kenne Bell. Made 616rwhp and 550rwtq This car has absolutely everything done to it. Fore fuel system, 60# injectors, just re...

1988 Car Shop Manuals in excellent condition for their age: $149.95 Call 681-235-2167 and leave a message 1988 Ford Mustang Do It Yourself Service Manual 1988 Ford Mustang Electrical & Vacuum Trouble-Shooting Manual 1988 Car & Truck Engine/Emission Facts Book Summary 1988 Car Shop Manual...

Figured id start a thread over here. Posting drift videos for my foxbody. If anyone else here on corral drifts, post up some pics or vids. Other vids on my youtube, all at the same spot. So its like watching nascar for 300 laps, but way worse. lol. Helmet cam is bad here, will fix it for...

Really solid Vortech V-1 Head Unit For Sale. Made around 8lbs of boost on my setup. Recently upgraded to a bigger Vortech SCI HD Head Unit and just took this off of my car to swap it out. I have attached a video link of it running as well. It is in full working condition and ready to bolt on...

For sale a practically new Ford 4.0 sohc V-6 cam tool kit made by OTC part number 6488 only used once. $199 shipped Works on mostly all sohc v6 from 1997-2010.