Hello i cracked my lower intake manifold and looking at trying to upgrade i've seen the edlebrock performer and the holley systemmax lower intakes but just curious if they bolt up to the stock heads and upper intake manifold on my mostly stock 1989 mustang. just curious what fits the stock...
Looking for something similar to this Professional Products 54110
Or an mmr 5.4 to 4.6 intake manifold adapter plates
would also buy a billet set if anyone makes them.
For sale: Edelbrock Victor 5.8 EFI intake manifold for sale. Upper, lower, and 8 bolts. Good used condition but not perfect. One of the lower fuel rail bolt holes is messed up and it has a couple marks (see last three pictures).
Upper and lower have been port matched. Upper has also been...
Hi Everyone,
Up for sale is an Edelbrock RPM upper and lower intake manifold for Foxbody 5.0. It was previously run on a 1993 Mustang GT with no issues. I'm asking $400 obo plus shipping.
Text me at 347-325-4731 if interested. Manifold is located in Central New Jersey.
Selling a Black TrickFlow Track Heat Intake. Upper part number is Tfs-sbf-Efi-2u. I purchased the intake and never used it. The guy I purchased from installed in it, but never drove the car so it's practically new. Comes with spacer, and temp sensor Asking $475. plus shipping
I was only able to...
Trick Flow Valve tall valve covers.
I have a Edelbrock Performer 5.0 Intake with the explorer throttle body and Trick Flow valve covers for sale
$200 for the intake
$125 for the valve covers.
OBO Trying to sell ASAP
EDIT: Intake has been sold.
SOLD
Selling my Edelbrock 2828 Intake Manifold. Fully Ported, Converted to EFI (Includes Edelbrock fuel rails), and milled to fit 9.2 deck engines. This would cost nearly $2000 to replicate. Asking $1000obo shipped inside the USA.
Located in Scottsville, KY 270-619-3472
*DOES NOT COME WITH HEADS...
Selling a reproduction Cobra Upper and Lower intake.
All sensors and heater tubes can be included at no extra charge.
One of the longer bolts (the longest) broke at some point and was replaced with a piece of all-thread with a lock-nut and washer that holds the torque spec perfectly. All other...
Does anyone make a lower intake stud kit for the 302? Has anyone ever ran one? To me it seems like it would make setting the gaskets properly a lot easier...
I have for sale a very clean (like new) Edelbrock Torker intake. It has been cleaned and the mating surfaces polished. Prepped it to put on my motor before deciding to go tunnel ram. All the hard work is done you just have to install and haul @$$! I was asking $195 plus shipping. New...
I have a spare PI intake manifold for sale.
This manifold is in great condition with no cracks/defects.
It's a bit dusty from sitting around but works great.
Asking $90 + Shipping.
Up for sale is a factory GT500 lower intake manifold with intercooler core, and a custom Hogan upper hat. perfect for any 5.4/5.8 DOHC turbo build. email [email protected] for pricing and pictures.
Nearly new track heat came off of my 93 GT when I sold the car. Swapped to a completely different setup in the notch I'm doing. hard ware was bad, but I'm including a 1/2" spacer with it. 450+ shipping. price is firm
I'm looking for a PI intake if anyone has one.
The heater hose nipple on the one I have right now is on it's last leg and i'm gonna need a replacement.
I would like it with the aluminium crossover preferably, but not required.
I'm located in 91915.
Selling a near complete TrickFlow Track Heat intake for the 2V. Comes in the wrinkle black finish and includes both the standard upper plenum which uses up to a 75mm TB as well as the upgraded upper plenum which uses a twin 57mm tb like the 99-01 cobra (twin 57mm tb included). The intake...
75mm Trickflow Thottle Body
I have a 75mm Trickflow thottle body only. Came off a 03 Mustang.
Asking $200 obo
Or let me know what you have for Trade
Thanks