Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 331 Results
  1. Exterior Parts
    They only make one. Pm me if you have one for sale. need it asap, can’t wait the 4 weeks. willing to pay. Thanks, Layzie
  2. The Body Shop
    Good Moring all, Just picked up a 92 Gt. This is the fifth fox I’ve had over 12 years. Bought it as a project, it’s no show car and I don’t plan on making it that way. Just a nice cruiser to enjoy and not worry about where I park it. The carpets were out of the car and I found two small rust...
  3. The Body Shop
    here it is, im far from finished, but from what i know this is only the second foxbody removable hardtop that doesnt look like dogshit, its not painted, its still got alot fo finish work to be done, but its a start for something great.
  4. Superchargers
    I have gave myself a break from the car the past few years. Just got burnt out building it and wanted to finally enjoy it. I am ready to start tackling some issues again. SC fox with AFR heads. Runs good, but MA temp is through the roof! I told the EFI to not pull timing till 187 degrees...
  5. Classic Mustangs & Fords
    Hey y'all, Threw a battery in my project after installing a new fuel pump relay. Nothing. At key off, every pin is 0V; Key on, 0.3V. Same reading at both the inertia switch and the relay. What's a good place to start tracking the problem down? Thanks
  6. General Mustang Tech
    Anyone out there who could possibly guide me with what could be wrong with my car To start I had goofed and placed the positive 3g alternator wire to ground and I cooked my ecu and popped the alternator fuse From this screw up I've changed the following New harness 302(93 year specific)...
  7. 5.0/5.8 Engine Tech
    I am building a 351w for my foxbody Mustang. I’m using the stock bottom end with AFR 185 enforcer head and keeping it EFI with 30lb injector. I’m using a t-5z trans and have 3.73 rear-end gears. What are some cam recommendations that will increase HP and torque with a good idle and keep the car...
  8. Windsor Engine Parts
    Like brand new Trick Flow stage 1 cam. Just pulled from my 89 today. Only has about 300 miles on it. Excellent condition. All of the journals and lobes are immaculate. Cost over $300 new plus shipping. Looking to get $200 plus shipping for it. Located in Glendale AZ.
    $200 USD
  9. General Mustang Tech
    Is under the dash in the driver side in my 1993 mustang
  10. Mixed-platform Engine & Drag Racing Tech
    Anyone ever do a 5.9 isb 24v cummins in a 90 foxbody notch? questions concerning fitment in engine bay, suspension recommendations, what all id need to beef up (rear end, motor mounts, sub frame connectors, etc), cooling, trans recommendations (prefer manual)
  11. General Mustang Tech
    Hey all! I figured since not much is out there about actually doing the swap, then I'd post my journey for future people who may want to do it. Warning! It's not a simple swap. I was just stubborn and wanted to keep the MT-82 since I already had it with my 5.0 Coyote engine. Since I...
  12. Wheels and Tires
    Car is 100% stock until now. My mechanic just done 5 lug conversion on my 90 LX 5.0 with a kit from CJ Pony parts. I purchased a set of wheels and tires off marketplace. Bullet wheels with 245/45/17. Stamp on back of wheel says 17X8 with 45mm offset. When you mount the fronts, they are...
  13. Electrical & Wiring
    I got a 1985 LX mustang originally a 4 cylinder automatic, now swapped with a 302 carb and T5 full Msd ignition. My question is, I’m currently trying to wire AC back into the car I have the dash pulled and the air box out, I have a service manual with all the wiring diagrams and have found the...
  14. General Mustang Tech
    I recently bought this two piece oil pan gasket for my 93 5.0. Will i need to drop the k-member or lift the engine to install this one? It seems like I can just slip it in if I drop the oil pan half an inch. Has anyone used this gasket before? Thanks.
  15. Suspension
    Like new complete Steeda springs with KYB rear shocks, decided to use coil over setup. Nothing wrong with springs or shocks. $300 OBO willing to ship at buyers expense/shared cost.
    $300 USD
  16. Electrical & Wiring
    Hello, I’m wondering is there a way to cut the two wires coming off of the brake light switch and run my own wire with an in-line fuse to the brake light hot wire, then to the battery to keep it from going through the fuse box? The reason I’m asking is because I keep blowing HAATB fuses on my...
  17. General Mustang Tech
    Evening All, Running into a little bit of an issue with a new fuel system I just installed on the foxbody. No matter how much I turn the set screw on the regulator, I can’t get the pressure at the gauge to move up or down. With the engine off and pump on, it shows too high of a pressure, with...
  18. General Mustang Tech
    Hello, I have a 92 Gen 2 manual swapped fox. I am having an issue with wiring. First I’ll start with the car runs great. No issues at all. But when I turn the headlights on for night driving that’s where I have an issue. It blows a fuse almost instantly (there has been a few times where it lasts...
  19. Drivetrain
    My 1990 auto 5.0 fox was working flawlessly but I got bored and wanted to reset my idle screw and TPS voltage. I did it exactly as in the brew2l video, the car wouldn't idle with the IAC unplugged if that matters for this question but I set the screw so it did and got the voltage at .99. After...
  20. General Mustang Tech
    I currently have a 93 manual 2.3 and have been looking for swap parts for awhile and now have the opportunity to buy a whole car. It is an 88 5.0 and in running condition but doesn’t have a title. My main concern is wiring, and was wondering if anyone had an experience with it. I know the wiring...
1-20 of 331 Results
Top