Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 20 Results
  1. 5.0/5.8 Engine Tech
    Hey guys, So I just converted my stang from a t5 to a 4r70w. I'm having a issue now that when I go into 1st or reverse the car dies . I have a terminator x for ecu , the trans is a built trans with a manual valve body witha brake for reverse. Warm or cold doesn't seem to make a difference...
  2. 5.0/5.8 Engine Tech
    Hey guys , Looking for some help . I did a battery relocation on my fox . I used 1/0 welding cable and I want to put in a inline fuse. I'm not really sure what size Fuze I should go with . I have dual electric fans that are 42 amps combined and I have a 130 amp alternator . I do have some other...
  3. Holley EFI Systems
    New to tuning and trying to get a solid E85 base tune on my terminator x for my turbo Foxbody. Can anybody help?
  4. 5.0/5.8 Engine Tech
    Hey guys , So I changed my oil yesterday and it smelled like straight fuel and felt thinner. I have noticed that it would smoked alittle on start up but would clear within couple mins . Also if I shut it off and tried starting the car up again I would have to hold the throttle wide open and let...
  5. General Mustang Tech
    Hey guys, So im looking into converting my t5 to a aod . Gots me a couple questions cause I'm not really to sure about couple things here. To start I have a 89 lx . Has a 302 with a 90mm maf 60 injectors b303 cam and a vortech charger at 15 psi . Sct tuner . With 3.73 gear . Car made 509 on...
  6. 5.0/5.8 Engine Tech
    Hey fellas, So I got my car tuned up runs great . Dynod 509 hp 497 to. I got it registered and on the street. New problem . Anytime I'm trying to cruise. It starts bucking like a horse. Only thing that changes it is either alittpe throttle or push the clutch in. It doesn't seem to like a miss...
  7. 5.0/5.8 Engine Tech
    Sorry to keep bothering all you but I'm trying to learn my way and fix my hooptie. So I have a 91 fox 60lbs injectors 90mm maf . B303 cam with a vortech v2 and sct chip . I'm having problems being lean . Wideband is pinned past 20 I also have code 91. I checked voltage at o2 sensor and even...
  8. 5.0/5.8 Engine Tech
    Question for you guys . 302 vortech v2 , 60 lbs injectors, 90 mm maf , b303 and sct tuner . Do I need to have the bottom side of the map sensor hooked up.to vacuum or does it just dump out ? Thanks in advance
  9. 5.0/5.8 Engine Tech
    Soo I'm back again . Finally got the car running great. Now only question is . The way the car was set up when I bought it had some ghetto pcv setup. As of now I have the pvc valve hooked up to the side of the upper intake . And a check valve in-between. The oil fill neck has a port for a tube...
  10. 5.0/5.8 Engine Tech
    What's everyone using for distributors? Got some junk aftermarket one on right now . Want to get rid of it . 302 60lbs injectors 90mm maf b303 cam vortec v2 . Thanks in advance
  11. 5.0/5.8 Engine Tech
    91 foxbody . 302 with 60lbs injectors , 90mm maf , vortech v2 . B303 cam advanced timing to about 14 degrees per tuner and fuel pressure at 32 psi with vacuum on. Has a sct chip . Problem I'm having when I start er up fires right up rpms go to about 1200 then come down to about 1000 chills for...
  12. 5.0/5.8 Engine Tech
    Can anyone point me in the direction of a 8 rib belt . Measured with a string came out 53.5 inches . Tried searching the interweb but to much other random stuff pops up . It's for my 302 fox vortech v2 . 3.33 pulley and 6 3/4 crank pulley I believe. I tried a 8k1380 and it was about a inch to...
  13. 5.0/5.8 Engine Tech
    Hey fellas , So im installing the sve 3 g alternator from lmr . It came with a 4 gauge wire to go from the alternator to the battery . My question is do i still jeed to use the original black and orange wire that came out of the alternator to the starter solenoid? I feel as if that kinda...
  14. 5.0/5.8 Engine Tech
    Hows it going guys . Any of you by anychance have a single speed pro piston for sale ? Part number L-2488F . Got a brand new set and broke one while installing and I really don't wanna buy a hole new set . Waste of money . Thanks in advance
  15. 5.0/5.8 Engine Tech
    Well my rod decided it wants to turn into a Twizzler yesterday. So what to do now ? Do I hope the block itself isn't jacked up and rebuild a stock bottom end ? Do I get engine work done make it a 347 ? Can I reuse my old heads and intake and stuff in general? Or do I say screw it and just do a...
  16. 5.0/5.8 Engine Tech
    So I got a new problem fellas . Backround 90 mustang with vortech v2 . 60lbs injectors 1.7 skorpion rockers. B303 cam . Aero 340 fuel pump. Sct 90mm maf . And sct chip . Advanced timing 10 degrees . Problem im having is car fires right up runs really rough. Smells really rich . I tap the...
  17. 5.0/5.8 Engine Tech
    Okay so I got my new maf sensor along with the 6 pin pigtail to solder in . Now only problem all the wires on the pigtail are black . Anyone have a Schematic or instructions on how to wire 4 to 6 without blowing up ecu ? Thanks in advance
  18. 5.0/5.8 Engine Tech
    Whats everyone running for fancy valve covers . I'm having trouble with the ones I bought . To tall and the holes are in the wrong spot . On passenger side the hole is in the back towards firewall which get in the way of the throttle braket . And driverside where I was gonna run the pvc is in...
  19. 5.0/5.8 Engine Tech
    Hey guys , New user here so bare with me . So I have a 90 mustang that is charged with a vortech v2 with 10 rib pulley . Has a b303 cam, 340lph fuel pump woth a regulator . And 60 lbs injectors . Have a sct chip not yet tuned and a maf sensor not installed yet . Anyway im dropping the motor in...
1-19 of 20 Results
Top