Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-15 of 15 Results
  1. 5.0/5.8 Engine Tech
    Hey guys, So I just converted my stang from a t5 to a 4r70w. I'm having a issue now that when I go into 1st or reverse the car dies . I have a terminator x for ecu , the trans is a built trans with a manual valve body witha brake for reverse. Warm or cold doesn't seem to make a difference...
  2. 5.0/5.8 Engine Tech
    Hey guys , So I changed my oil yesterday and it smelled like straight fuel and felt thinner. I have noticed that it would smoked alittle on start up but would clear within couple mins . Also if I shut it off and tried starting the car up again I would have to hold the throttle wide open and let...
  3. General Mustang Tech
    Hey guys, So im looking into converting my t5 to a aod . Gots me a couple questions cause I'm not really to sure about couple things here. To start I have a 89 lx . Has a 302 with a 90mm maf 60 injectors b303 cam and a vortech charger at 15 psi . Sct tuner . With 3.73 gear . Car made 509 on...
  4. Drag Racing
    Hello everyone, I am new to the forum and was wondering if someone could clear this up for me. I have a 1992 Mustang GT that I plan on racing in the NHRA Super Stock category. I was reading the rules about “Engine Modifications” and it states that (Quote) “Any intake manifold permitted...
  5. 5.0/5.8 Engine Tech
    Hey fellas . Can anyone tell me how to wire in aftermarket check engine light ? I know the light is supposed to be negative polarity. Anyone got the wire colors I need to hook up to ? 90 lx . Thanks
  6. 5.0/5.8 Engine Tech
    Hey fellas, So I got my car tuned up runs great . Dynod 509 hp 497 to. I got it registered and on the street. New problem . Anytime I'm trying to cruise. It starts bucking like a horse. Only thing that changes it is either alittpe throttle or push the clutch in. It doesn't seem to like a miss...
  7. 5.0/5.8 Engine Tech
    What's everyone using for distributors? Got some junk aftermarket one on right now . Want to get rid of it . 302 60lbs injectors 90mm maf b303 cam vortec v2 . Thanks in advance
  8. 5.0/5.8 Engine Tech
    91 foxbody . 302 with 60lbs injectors , 90mm maf , vortech v2 . B303 cam advanced timing to about 14 degrees per tuner and fuel pressure at 32 psi with vacuum on. Has a sct chip . Problem I'm having when I start er up fires right up rpms go to about 1200 then come down to about 1000 chills for...
  9. 5.0/5.8 Engine Tech
    Can anyone point me in the direction of a 8 rib belt . Measured with a string came out 53.5 inches . Tried searching the interweb but to much other random stuff pops up . It's for my 302 fox vortech v2 . 3.33 pulley and 6 3/4 crank pulley I believe. I tried a 8k1380 and it was about a inch to...
  10. 5.0/5.8 Engine Tech
    Hows it going guys . Any of you by anychance have a single speed pro piston for sale ? Part number L-2488F . Got a brand new set and broke one while installing and I really don't wanna buy a hole new set . Waste of money . Thanks in advance
  11. 5.0/5.8 Engine Tech
    Well my rod decided it wants to turn into a Twizzler yesterday. So what to do now ? Do I hope the block itself isn't jacked up and rebuild a stock bottom end ? Do I get engine work done make it a 347 ? Can I reuse my old heads and intake and stuff in general? Or do I say screw it and just do a...
  12. 5.0/5.8 Engine Tech
    Okay so I got my new maf sensor along with the 6 pin pigtail to solder in . Now only problem all the wires on the pigtail are black . Anyone have a Schematic or instructions on how to wire 4 to 6 without blowing up ecu ? Thanks in advance
  13. 5.0/5.8 Engine Tech
    Hey guys , New user here so bare with me . So I have a 90 mustang that is charged with a vortech v2 with 10 rib pulley . Has a b303 cam, 340lph fuel pump woth a regulator . And 60 lbs injectors . Have a sct chip not yet tuned and a maf sensor not installed yet . Anyway im dropping the motor in...
  14. 5.0/5.8 Engine Tech
    Hello, im new here and trying to get my 86 gt running with no problems. Currently it overheats and also stalls randomly (I think it might be the TFI module). Anyways I’ve already changed the thermostat, pulley belt, some radiator hoses, and radiator cap but no solution. I think I might’ve...
  15. 5.0/5.8 Engine Tech
    331 stroker scat crank and rods probe pistons, billet steel main girdle. $600 Trick flow 170cc fast as cast heads woth tfs double springs $750 comp rockers $75 canton oil pan $100 track heat intake upper n lower $250 lots more parts 70mm bbk tb bbk headers and x pipe 30lb inj bbk billet fuel reg...
1-15 of 15 Results
Top