forged

For Sale 480-255-5427

SOLD! Thanks Corral!

Hey guys, been awhile since I have posted on here but going to re-post this from some time back and hopefully make someones day. I have an mmr 900 engine, build sheet pic is below that has been sitting garaged on the engine hoist for a few years. I am in the process of moving, and its obvious...

I have a set of -11.5cc standard bore forged Diamond pistols. They sat in my garage for awhile after buying them and I had them cleaned up. At the bottom is the link to the craigslist ad that contains the pictures of the pistons. The pistols go for $724.99 and I am asking $400 unless someone...

347 stroker w/ stock block Scat forged crank from machine shop still in bag Forged Ross XL400 pistons (accepts TW heads too) Not sure who makes the rods Main studs w/ main girdle Main caps were grinded for more surface for the girdle to contact Cam bearings were changed Crank was cut I believe...

I am toying with the idea of selling my engine and going a different route. It is a fully built 327 cubic inch stroker. Same as a 331 but with a standard bore. The engine has very little time on it. A handful of dyno passes, 3 track passes and about 500 street miles. Here are some specs on the...

-SOLD- SOLD -Speed Pro 30 Over Forged Pistons SOLD- SOLD Pistons are sold! TY CORRAL!

Started collecting parts for a build, but life said "nope" and money had to go another direction right now. 18cc forged pistons (standard bore), standard length forged rods with arp2000 rods- $500 shipped Trick Flow cams w/ springs part number TFS-51802002 less than 100 miles. Installed right...

any input is appreciated I have a 99 cobra that motor is going to be freshened up, starting the build this month. i'm looking to get out of this build as cheaply as possible but with as many new parts as possible. will be going .020 over and looking for around 10.5:1 compression. power adder...

1000hp+ 331 short block Looking for a 331 stoker short block that is capable of handling 1000hp or more. Will only be running around 750-800 daily driving but will be able to push atleast 1000hp so I want it to be able to handle that power without fault. Would be needing it soon. Will pay for...

I have quite a few stock and performance sbf parts for sale. Ford svo 1.72 roller rockers- 180$ 94-98 aluminum driveshaft- 175$ edlebrock low pro valve covers-75$ 94 lightning block with with crank only minor cylinder wall damage above top ringland-300obo picked up used edelbrock...

1988 Mustang GT with 331CI Boss block, Trickflow heads, D1 Procharger with intercooler. New AOD built by ATI with a new converter, 8.8 with 9" ends, newer tubular control arms. Full fuel system. It is tuned for pump gas, drive anywhere, doesn't get hot and drives very nice. I have a ton of...

Hello all! Just joined forum today for some advice from the experts. I recently purchased an 01 cobra for $5300. I bought it August 3rd and it had 94,000 miles on it. I traveled around four hours to get her knowing it needed a throw out bearing and the body was not perfect. Needless to say I...

sold

All like new condition used on test engine. Parts are clean and ready for install. Fully forged sx -18cc pistons with moly rings. Fully forged floating I beams. 3/4 inch billet aluminum DSS main support system with arp bolts pistons also have arp connecting bolts. Also have a forged iron crank...

Sc swap heads included needs belt, intercooler set up and maybe a few other thing, have all injectors, fuel lines, rail, throttle body as well as a gt throttle body, have all bolts, plenum everything. Also have a brand new forged crank, forged sc rods and .30 over pistons. Pistons and rods are...

I am cleaning out the garage and found these in a box of parts I received a while back with a 302 I purchased. They are coated stock forged pistons (E7ZE-CA): IMG_5304 by Strike_Zero, on Flickr IMG_5305 by Strike_Zero, on Flickr These are the worst ones: IMG_5308 by Strike_Zero, on...

SOLD!

SOLD!!!!!!! Thanks!! I have for sale (8) brand new forged dished pistons from Probe. These are for a 351w with standard bore. Pistons only, no rings. $225 Shipped lower 48 US FRT-2601-STD Compression Height: 1.785 Bore: 4.00 Rod: 5.956 Pin: .912 Ring Grooves: 1/16, 1/16, 3/16 Dish: 17cc

SOLD! Blower/Meth Kit/42's/LMAF will be for sale soon