Ford Mustang Forums banner
exhaust
1-18 of 163 Results
Advanced
  1. 94/95 Tech
    I have a 1994 5.0L Mustang, and took a pair of GT40P heads off of an Explorer (can’t remember year). I know there’s several posts about correct-fitting exhaust headers, but I can’t seem to find any for sale. I’ve searched for MAC, FRPP, and Motorsport, but I couldn’t find any for sale. Will I...
  2. Exhaust Parts
    I have a Pypes O/R x-pipe for sale. I just switched it out for a mac prochamber. Sounded great with my borla stingers, 100 obo
  3. Exhaust Parts
    Got a set of axle backs I don't need - they are an unknown brand, possibly a custom job with some sort of bullet muffler. If you want to hear what they sound like, I made a video on comparing them with the Roush ABs here. You can hear them at the 7:30ish mark. I got them second hand from...
  4. Exhaust Parts
    For sale: Roush axle backs for 2011-2014 Mustangs. I had these on my 2014 GT for about five years, approximately 60k miles. As you can see from the pics, they could use a little bit of polishing but I haven’t had any issues as far as leaks and they sound great. Getting rid of them because I want...
  5. GT & SOHC
    I have a 2004 mustang gt with cai, off road x pipe and catback exhaust. When i revved it today i noticed a little wet spot on the ground behind the car. I ran my finger in the exhaust pipe and smelled it and its fuel. Is this normal? If not what could be causing this? Thanks, Trevor
  6. S197 Mustang GT (2011-2014)
    I picked up these axle backs second hand a few months back. Nobody really seemed to know where they came from (seller wasn’t sure either) so I’ve started calling them the “mystery mufflers”. This got them installed on my 2014 GT and made a video of the install and a sound comparison between...
  7. Exhaust Parts
    Dynatech LS Swap headers for a foxbody, will fit perfectly with a UPR or AJE K-Member. I have welded on V-Bands to make for easy exhaust removal. I am also selling my X-Pipe that has V-Bands welded as well. Fit perfectly on my 1987 Foxbody, will fit any LS fox from 1979-1993. Dynatech 1 7/8...
  8. Power Adders For Sale
    For Sale: Pair of Master Power turbine housings P-trim .68 A/R T4 undivided inlet 3" v-band outlet $200 Location: Indiana, 46711 email: adynes(at)gmail
  9. Exhaust Parts
    ////Sold//// Listed are New MAC Chrome exhaust 2-1/2" Tailpipes for a 64.5-73 Mustang. I intended to use this on a 1966 Ford Mustang. This should work on most 64.5-73 Mustangs with dual exhaust. Asking $115 So, this is a good deal for high performance exhaust components (compare with vendors...
  10. Exhaust Parts
    ////Sold//// Listed is a 3" x 3" Dr. Gas Exhaust Crossover kit with Summit header collector, I intended to use this on a 1966 Ford Mustang (with headers). This should work on most 64.5-73 V8 Mustangs. actually since it is a cut and weld to fit solution it should fit most applications using a 3"...
  11. Exhaust Parts
    I have a 3 inch Mac prochamber for Fox body Mustangs in excellent condition I'll take 175 plus shipping for it. Call or text me @ 3013953921
  12. Exhaust Parts
    ////Sold//// Posted are exhaust components purchased for an early model Mustang Exhaust system (excluding the mufflers), I intended to use this on a 1966 Ford Mustang (ideally with headers). To the best of my knowledge, this should work on most 64.5-73 V8 Mustangs. Add your own favorite...
  13. Exhaust Parts
    DOUG THORLEY TRI-Y 1 5/8 Longtube Headers for 302 Foxbody Mustang SOLD!
  14. Exhaust Parts
    Stock 2011 GT500 Mufflers and catted h pipe that I removed from my GT500 to install full exhaust. These have about 3,000 miles on them and came off a weekend cruiser that I've owned since new (AZ Car never seen rain etc). Located in Phoenix, AZ 85027 and asking $200 for Mufflers and $100 for...
  15. Blog
    I have recently purchased a cat back SLP Loudmouth exhaust for my 02 Mustang GT and went to put it on earlier today but only to get stumped. My buddy and I jacked up the car and tried to disconnect the old exhaust from the H-pipe but the 4 bolts on the two flanges were rusted shut. We sprayed...
  16. Exhaust Parts
    Selling my Mac ceramic long tubes and Prochamber for a 302 sbf with a manual transmission. They are 1 5/8 with a 2 1/2 collector. Only have about 100 miles on them. Just bought a turbo, so need these gone. Asking $550 both both. Rather do local, but can ship at buyers expense. Text me for pics...
  17. General Mustang Tech
    2000 GT stock exhaust and I am wondering if SLP LM mufflers will fit on stock setup??? Also, anyone know if this will affect emissions testing in Cali?
  18. GT & SOHC
    99 GT, Sean Hyland cams, Kenne Bell 1.7. First a little background..I just finished replacing the front engine/timing cover. (long story) but it had an SCT timing adjuster that I removed and simply plugged in the crank sensor. Started the car. It's missing at least one cylinder and is dumping...
1-18 of 163 Results
Top