Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 154 Results
  1. Powerplant
    Hi I have a 2003 3.8l mustang one day it broke the timing chain and cylinder 6 valve hit piston and broke the valve messing up the piston. We rebuilt the engine with new pistons, bearings, and a camshaft. When I try to start the engine it runs rough for a few seconds and dies. Right before it...
  2. SVT & DOHC
    I recently purchased a 97 cobra it has 59,400 miles, I drove it to work these past two days and today the check engine light came on while on the highway. I got a scanner and checked it Engine Code p1516 came up which I looked into and it said that my (IMRC open or closed longer than expected.)...
  3. General Mustang Tech
    Hi! I was replacing my thermostat and housing and one of the bolts was stuck real bad so I took the lower manifold out and had it machined. Then I reinstalled everything and now it won't start. When I took the distributor out I didn't make sure it was at TDC so I'm pretty sure the timing is way...
  4. 94/95 Tech
    Hello everyone! I own a 95’ Mustang GT I live in Brazil and there’s no mechanic around that is capable of working on the car, neither someone who went through same situation, since there is only around 450 GTs in the whole country. Car just died, engine spins but there’s no signal of spark, it...
  5. General Mustang Tech
    I have a mustang ecoboost 2017. Recently the car started misfiring and there's delay in starting the engine and sometimes it cuts off the power in the middle of the road and turns off without having electric power, I have changed the spark plugs, fuel pump, high pressure pump, and purge valve...
  6. GT & SOHC
    So my heads are warped on my 96 gt and instead of putting new heads and resurfacing the deck and everything I decided its easier and cheaper to just put in a pi motor, I found one out of a 03 mustang gt at the junkyard and that's what I plan on getting, it would come with no accessories so what...
  7. General Mustang Tech
    Im just wondering if the ECMs are interchangeable cause I have an extra ECM from a 4 cyl that I want to sell
  8. General Mustang Tech
    I just finished a 4cyl to 8cyl swap. The car came with an ECM that I am not using because I have my 8cyl ECM in. My question is, will the ECM that came with the car work for a V8 application? also, what years will the ECM work on? Its for a 1991. I’m just looking to sell it and see if its...
  9. Miscellaneous Mustang Parts
    4.6 with lunati vodoo stage 1 cam build. 1998 block completly reworked and built all the wat up. Including new $500 intake and so on. Only primed and started 7sec never installed after build.
    $2,200 USD
  10. S197 Mustang (2005-2010)
    Hello, as the tittle says I've got a V6 2005 Mustang. My thermostat housing blew and shot out all my coolant. I pulled over towed my car somewhere safe and replaced the thermostat housing. Unfortunately, on the way home it still had issues that lead me to believe that I had blown a head gasket...
  11. 5.0/5.8 Engine Tech
    Hey just looking for a bit of advice got a 1989 5.0 fresh rebuild just bought an assembled short block... but on 61cc aluminum heads trick flow intake bigger cam ect.. but I think I this engine could use a little more compression.. it has what look like sealed power hyperutectic pistons and was...
  12. Automotive Tools
    ARP Ring Compressor 4.030" 900-0300 https://photos.app.goo.gl/QAJsPGKS3ZQ5fSnE6 This is a brand new, never-used tool. I bought it new in early 2003 for a project that never materialized. I'm selling all of the parts -- all new -- for a 408 small block Ford build, plus some tools and Fox...
    $40 USD
  13. S197 Mustang (2005-2010)
    Anyone in Florida selling this Ford Racing cold air intake?
  14. GT & SOHC
    I currently have a 2003 Gt with a rod knock and I was wondering if an engine out of a 2008 mountaineer would be a suitable replacement. I got the motor for cheap and I know that id have to replace the top end stuff but would I be able to make it work?
  15. Powerplant
    Im in the middle of a 4v swap into my 99 GT and now im running into an issue. Im trying to reinstall the new engine back in with long tube headers on it and the engine is not wanting to go back in. It looks like the header on passenger side is rubbing against the side if the engine bay and...
  16. Modular Engine Parts
    Looking to buy 4.6L DOHC short block asap. Im located in Sothern California and can travel some for a good short block.
  17. S197 Mustang (2005-2010)
    I have a 2005 Mustang GT and have been having this problem for a while now. Whenever I drive the car, my fan to cool the engine will initially turn on but after it shuts off, it will not turn back on. This causes the car to begin to overheat when idling. I am not running any A/C when this...
  18. 5.0/5.8 Engine Tech
    Hello everyone. Just wanted to get some advice on a build i plan on starting next month and wanted some recommendations on if I am heading in the right direction with my build. Advice is very welcome as i have not torn down a motor in quite some time. I am looking to keep this 550+ streetable hp...
  19. Windsor Engine Parts
    For sale is a Edelbrock Victor EFI intake, pt # 2945, intake for sale. I bought used but appears to be in good condition. SOLD.
  20. 5.0/5.8 Engine Tech
    Hey everyone, just wanted to see what I am in for, but looks like I had a roller lifter that spun on my 5.0 roller engine. Portion on the bottom of the lifter wheel has been flatten out. Engine was rebuilt a few years ago, but only has a couple hundred miles on it as rarely driven. It is...
1-20 of 154 Results
Top