Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 103 Results
  1. Windsor Engine Parts
    I have a clean victor 5.0 intake I want to trade for a Holley systemax for a 302. comes with bolts and new gasket set LMK what you have
  2. Windsor Engine Parts
    I picked these up for a project and am changing directions. Would like to get what I paid for them. They are bare Pro Comp 190cc heads with 2.02/1.6 valve openings, and have 7/16’s rocker studs and guide plates. I am asking $450 plus shipping.
    $450 USD
  3. Windsor Engine Parts
    For sale: Edelbrock Victor 5.8 EFI intake manifold for sale. Upper, lower, and 8 bolts. Good used condition but not perfect. One of the lower fuel rail bolt holes is messed up and it has a couple marks (see last three pictures). Upper and lower have been port matched. Upper has also been...
    $1,250 USD
  4. Windsor Engine Parts
    I have a old school Downs upper intake with gt40 lower that has port work done to the head side. Also comes with 1" spacer. Works as expected. Very similar to the Ron Anderson (Anderson Ford) RAP intake. These were commonly referred as a "breadbox" intake. Private message me or text me for...
  5. 5.0/5.8 Engine Tech
    So I am about to start modifications soon, trying to decide between the Trick Flow Track heat stage 2 kit or piece together an Edelbrock RPM2 and Edelbrock parts mimic the Trick Flow kit. What are your thoughts?
  6. Windsor Engine Parts
    I have a tmoss ported intake. its still on the car. no damage or stipped bolts. I have paperwork showing before and after flow numbers. flows better then a holley systemax out of the box. I have had this intake for the last 10 years. 500.00 if picked up near St louis Mo. will...
  7. Windsor Engine Parts
    For sale is a Edelbrock Victor EFI intake, pt # 2945, intake for sale. I bought used but appears to be in good condition. SOLD.
  8. Modular Engine Parts
    Upgraded to a new Trick Flow setup and supercharger. This was an excellent intake for me, just upgraded to a bigger one. The specs are identical to the Edelbrock RPM. The only difference is that this intake was made in China. Use with Edelbrock gaskets.. It operates at an RPM range between...
  9. Windsor Engine Parts
    Stage 3 Pro-Comp 190CC Aluminum Heads, 4-Sets of Hardened Pushrods ALL + ACTUAL SHIPPING - Pro-Comp 190cc Aluminum Cylinder Heads #3036 with 2.02 / 1.6 valves. Nice Stage 3 Port Work. Fresh valve job, new comp cams valves. Needs rocker stud holes redrilled and tapped. Unmilled, very low miles...
  10. Windsor Engine Parts
    Up for sale is the Edelbrock Victor 5.0 intake and 1" spacer shown in the pictures. Was setup for multiport nitrous but all nitrous bungs are screw plugged and ready to run. No bolts. Fresh wrinkle black powder coat. Asking $550 obo. Lower has been oven baked silver since the first two...
  11. Windsor Engine Parts
    Hey guys i'm going carb so I won't be needing these pieces. 500km on everything, came off a 347 sbf. -Edelbrock Performer EFI Intake Manifold Upper & Lower 3821 Comes with all hardware as well as gaskets. $600obo -BBK Cold Air Intake w/76mm c&L maf Comes with maf, all clamps, air filter...
  12. Windsor Engine Parts
    I have a bbk 70mm t.b and Edelbrock elbow adapter for sale. Comes with egr blockoff plate. Excellent condition! I'll sale the pair for $150. PM me or call /text me @ 3013953921
  13. Windsor Engine Parts
    I have an Edelbrock hydraulic roller cam part#2221. The specs are: .520/.520, 227/234, 112 Had it in a stock block 302 with some ported GT40 heads, Victor Jr intake and 750dp carb, C4 trans, 4.10 gears and went 12.08 on motor and 10.38 on a 225 shot! Cam is in excellent condition. Bought the cam...
  14. Windsor Engine Parts
    Accufab F90 throttle body 90mm $200 Edelbrock 3849 intake elbow $100 Located in Danbury, CT 06811 Both new unused, open box. The throttle body is a little dirty.
  15. Windsor Engine Parts
    Hello, I am selling some Edelbrock performer heads, these heads just got back from the machine shop. Just had a valve job, resurfacing, and exhaust valves replaced. I have a receipt to verify all of the work done. I am asking $1000 plus shipping, I am located in Layton, Utah. The price is...
  16. Windsor Engine Parts
    Edit: found it all, thanks. Looking for these parts. Edelbrock super victor EFI intake part #29245 Edelbrock 95mm intake elbow part #3849 Accufab 90mm throttle body Thanks
  17. Windsor Engine Parts
    Trick Flow Valve tall valve covers. I have a Edelbrock Performer 5.0 Intake with the explorer throttle body and Trick Flow valve covers for sale $200 for the intake $125 for the valve covers. OBO Trying to sell ASAP EDIT: Intake has been sold. SOLD
  18. Windsor Engine Parts
    Clean ready to go EFI 302 Edelbrock Performer RPM 2 lower intake with professional products Performer style upper. (we used rpm II upper on a Windsor build) $350 obo 936- three six six 56 zero 2 text or call 936-634-five six five 6 8to5. Located in Lufkin,Texas or email...
1-20 of 103 Results
Top