Ford Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 425 Results
  1. Superchargers
    I will soon enough be done my M112 Supercharged intercooled 5.0 and needed some info on ECU. The car is a 92 tbird 5.0, I am thinking of transitioning to the 96-2001 explorer coil on plug with cam and crank sensor. (Mainly for supercharger clearance) I was also thinking of getting a bigger MAF...
  2. Superchargers
    I am making a custom lower for my 92 5.0 tbird to adapt a m112 SC and I am in search of intercooler ideas. This is going to be an after cooler sandwhich plate in between lower and supercharger. I have very limited height clearance and therefore I am looking into using a motorcycle radiator as...
  3. Mustangs For Sale/Wanted, 1987-1993
    Respond to the craigslist ad if interested, I will not respond on here. Thank you. https://sfbay.craigslist.org/eby/cto/d/san-ramon-1993-mustang-gt-50-cobra/7557183046.html
    $35,000 USD
  4. Exterior Parts
    Looking to purchase a rust-free bubble hatch for a 1985-86 mercury capri.
    $1 USD
  5. 5.0/5.8 Engine Tech
    I have a 92 tbird 5.0 (same as 94-95 fox) and I am making a custom intake to adapt a M112 and need some help/info with injectors. I am planning on making in the range of 400-500FWHP and im not sure what size injectors to get. I will need to weld in bungs in my intake so the kind of injector...
  6. 5.0/5.8 Engine Tech
    I want to turbo my 68 mustang. I think it will be cheaper and more fun than building an n/a 302. I have a 68 302 with a stock 3 speed toploader behind it. I know cx racing has a kit you can only buy a kit for an automatic. So I have to put together my own parts. I am planning on leaving my 302...
  7. General Mustang Tech
    I have a 1990 5.0 with the original motor and T5 5-Speed transmission. MILES: 202,000 Shortly after my rear end rebuild with 4.10 gears and a short throw shifter install, everytime i've shifted into 3rd gear and gave it gas, it quite literally whines up like a supercharger (sound is...
  8. 5.0/5.8 Engine Tech
    Do not know much about the car other than what I see, 3 bar gt40 heads, tubular gt40 intake, stock tb, 19lb injectors. Not sure of cam or rr as I haven’t popped a valve cover off yet but it is not a stock cam. Car has a idle surge I replaced the iac and tps is good I believe it was .965 Now to...
  9. 5.0/5.8 Engine Tech
    I drive a little heavy footed… I have shorty headers and a k & n cold air intake on my 1989 mustang GT Convertible. Im only able to go about 116miles on a full tank. My car tends to surge quite bad while idiling. What is causing this bad gas mileage and can I fix it to get around the 13 range ...
  10. GT & SOHC
    Just a question Would love to see what everyone thinks, is it possible to get a 5.0 coyote block and just add SOHC 2V heads and slap it in an SN95?
  11. General Mustang Tech
    Hi all, Currently planning out my exhaust system, don’t wanna buy and install just to regret it and switch back. On my 5.0L (mostly stock), I currently have a small mixture installed: Factory 2.5” Headers (I believe they’re long tubes) Bassani X-pipe Borla Pro XS The cats ARE still in the...
  12. General Mustang Tech
    I pulled a 5.0 out of a 92 thunderbird for a foxbody but for some reason the lower intake gasket does not line up correctly. Any help is greatly appreciated
  13. 5.0/5.8 Engine Tech
    Hey just looking for a bit of advice got a 1989 5.0 fresh rebuild just bought an assembled short block... but on 61cc aluminum heads trick flow intake bigger cam ect.. but I think I this engine could use a little more compression.. it has what look like sealed power hyperutectic pistons and was...
  14. Drivetrain
    last night my 1989 for mustang 5.0 with a t-5 started making a ticking noise when driving or even when sitting idling unless I pressed in on the clutch. I have no idea what it could be I tried adjusting the clutch and I can get it to stop if I adjust the clutch almost the whole way but then it...
  15. 5.0/5.8 Engine Tech
    I am looking to build a 347 stroker out of a stock block 302 and I was wondering if it would be able to hold around 425rwhp semi reliably
  16. Power Adders For Sale
    Used Nitrous Outlet hard line kit for 2011-2018 Mustang / F150 with 5.0. Kit has the optional purge and nitrous bottle pressure gauge as well as the billet bottle bracket purchased separately. Works perfectly. Sold with bottle empty. Nearly $1,500 new. Selling for $900 OBO. Switching car to...
  17. 94/95 Tech
    Hey guys! I have a stock 1994 GT 5.0 convertible - Automatic trans I recently had the rear end rebuilt, went from the stock 327 to a 373 Yukon performance with a locker. I've thought about quite a few different mods but figured gears were the best place to start, Not sure how much heads, cam...
  18. Mustangs For Sale/Wanted, 1987-1993
    I have a 92' notchback with 30k miles on body. The car makes 1150 RW on 12 pounds. I am interested in selling the car. The asking price is 50k OBO, but am open to trades. Trades include a built Corvette z06, 69' Camaro, or 70' Chevelle SS. Serious inquiries ONLY. If interested, you can contact...
  19. 5.0/5.8 Engine Tech
    Hows it going guys . Any of you by anychance have a single speed pro piston for sale ? Part number L-2488F . Got a brand new set and broke one while installing and I really don't wanna buy a hole new set . Waste of money . Thanks in advance
  20. 5.0/5.8 Engine Tech
    Well my rod decided it wants to turn into a Twizzler yesterday. So what to do now ? Do I hope the block itself isn't jacked up and rebuild a stock bottom end ? Do I get engine work done make it a 347 ? Can I reuse my old heads and intake and stuff in general? Or do I say screw it and just do a...
1-20 of 425 Results
Top