Search Results for ‘4.6’

Hello I am new to the entire forum thing so I apologize if this is out of place or has already been discussed. I have a 96Gt with a 5speed and no mods other than shorty headers,Catless H pipe, borla catback and coilovers. I am facing a major overheating issue. The car has a new oe intake...

4.6 with lunati vodoo stage 1 cam build. 1998 block completly reworked and built all the wat up. Including new $500 intake and so on. Only primed and started 7sec never installed after build.

Hello everyone I'm looking for a set of intake adapter plates for the 4.6 2v to 5.4 2v . Like the 54110 or mmr ones. Let me know Thanks!

So out of all of the 2v,3v and 4vs 4.6 and 5.4 which is the easiest to make power

Hello, I'm new to the forums and currently in search for more information on swapping a 03 crown vic motor in my 97 standard mustang gt. I have most of the parts ready to go for the swap but does anyone know if everything will work if I can get the motors engine harness? I know it's COP vs the...

I bought a bare block used. I have installed the heads, oil pump and now I have moved on to installing the timing components. I bought the Cloyes kit from RockAuto and the drivers side installed fine. The passenger side is where the issue is. I have a roll pin in the place a bolt should be. I...

Had battery disconnected while I worked on it for a couple of weeks. When I turn key, I hear the fuel pump prime; and when key is in 'ON' position, NO theft light. However it behaves exactly like a PATS issue. It starts and immediately shuts off. Any ideas? Thanks

I have a 2004 mustang gt with cai, off road x pipe and catback exhaust. When i revved it today i noticed a little wet spot on the ground behind the car. I ran my finger in the exhaust pipe and smelled it and its fuel. Is this normal? If not what could be causing this? Thanks, Trevor

So I decided to do the whole pi swap thing. Did everything by the book and such. Put it back in the car and started cranking the engine. I didnt see any raise in oil pressure. After cranking 3 or 4 times for a couple seconds a squeak started. I thought it was the cam caps initially but its...

Email:[email protected] Portland, OR 615 9 six nine 41 six one 1998 Lincoln Mark VIII LSC Collectors Edition #071 4.6 4 valve Cobra motor 290hp/280tq 4r70W Transmission 3.27 Rear End (base model has 3.08) 161k miles HID Headlights NO accidents Car Fax included Clean title Passed DEQ...

Hey guys, Any advice on getting the starter out? I have BBK ceramic coated long tubes and stock K member on my '99 Mustang GT. All the searching I've done has mostly found threads where the person has stock headers and the advice is always to remove the mid-pipe, which I obviously can't do...

SOLD!

Whats up guys had a question on what a 2v engine (throttle body and plenum combo) and a TR3650 with i believe stage 1 clutch in it. Runs perfectly fine, i was given an suv with the bigger engine ill be running and will be going auto with plans of turbo :) I had a service warranty that was up at...

Ignition Coils off of a 2001 Cobra. Fits 99-04 4v Cobra or Mach 1 or Marauder. Most have Motorcraft stickers, the ones without the stickers have same exact shape and markings as the ones with Motorcraft stickers, so Im assuming the stickers just came off of a few of them. The car they were...

SOLD!

Sold

All, Doing some garage cleaning. I have my stock '02 GT Mid-pipe for sale. Worked great. Took it off some time ago for my pro-chamber. You'll need new hardware obviously. $100obo. Located near downers grove, IL. I can drop off if you are close and the timing works or you can pick up...

This is my first post on here but, after reading everything on this forum for help in the past, I've finally decided to reach out for some input on what could be causing the problems I'm having with my 2000 GT. For starters, I've learned a lot about my car over the last two months, I've...

SOLD!

Complete factory shaker intake setup with hood and hardware I'm parting out my azure blue 04 Mach 1 with an excellent body. I have access to a great freight packer and can send a pallet to most parts of the country for $150 (commercial address). Make an offer on anything you like. The more you...