Ford Mustang Forums banner
306
1-20 of 37 Results
  1. 5.0/5.8 Engine Tech
    Can someone tell me the proper way to set up gt40p heads to work with a roller cam with a lift near .590. I know about the crane kit. Im wanting to do this w/o using the machine shop. Thanks in Advance
  2. Windsor Engine Parts
    306 SBF 10:1 Comp Pumpgas Motor Eagle Crank And Rods Bullet Cam Edelbrock Ported Heads Harland Sharpe Rockers Victor Jr Intake [email protected] on Alky 10.90 On Pumpgas 50 Runs Since Freshened By Riegel Race Engines Very Consistent Bracket Motor.Late Rounds In Big $$$ Footbrake Races Every Showing...
  3. 5.0/5.8 Engine Tech
    Hi all, I have a 1991 mustang lx..tfs 11r 190s, rpm II, Ed Curtis cam, 24# injectors 306. The car has an auto computer in it but is a 5 speed now (not sure if that matters)....anyway...lately I have had this problem where I am driving the car around at low rpm and under light load (cruising)...
  4. Windsor Engine Parts
    Fresh 302 punched .030, out of an early 93 Thunderbird put together but never ran. Motor was being setup for a Ranger. Potential horsepower according to Ford Racing techs 450-500HP -Ford Motorsports x303 heads M-6049-X303 -Ford Motorsports gaskets (Head, Valve, Timing) -Ford Motorsports...
  5. 5.0/5.8 Engine Tech
    Hello, I have a 86 mustang that burns a ton of oil (1 quart every 100 miles or so) and I have since purchased a stock 302 out of an explorer. I currently have it all apart, and while I was looking at it I noticed I probably should get my crankshaft, cylinders, and heads machined (150k mile...
  6. Windsor Engine Parts
    Located in Danbury, CT. My email is [email protected] and I have a verified PayPal account with the same address. The short block is for local sale only!! 1985 xxx block with DSS main support girdle forged trw in-line fly cut pistons. timing cover to centerforce dual friction clutch. oil pan...
  7. Windsor Engine Parts
    AFR185 part#1422 price reduced.... I have a pair of AFR185's for sale. I bought a coupe with a 351W in it and got burned by seller. Motor had a roller lifter that had turned and ruined the cam. I just got these out of the machine shop after I had 1 of the heads repaired where the DA that...
  8. General Mustang Tech
    I'll start off by saying this is my first time on forums so bare with me lol. I bought my 3rd mustang, a 89' notchback 5.0 (carb) :salute: a couple months ago. I've spent a bunch of time since I bought it correcting some engine issues. But I'm needing some opinions before I just start throwing...
  9. 5.0/5.8 Engine Tech
    FIXED FIXED
  10. Windsor Engine Parts
    I have a stock block 306 available. Fresh out of the shop at Charlie Pepper's Racing Engines. Internals are all forged. Has a DSS main support and ARP hardware. Has heads bolted up to it that will be used elsewhere, so pics are difficult at the moment. I do not want to disassemble it until there...
  11. Mustangs For Sale/Wanted, 1987-1993
    Wanting to sell-1991 Ford Mustang Runs awesome but i broke the t5 5speed that was in it and never have time to fix cus i work on the road....bell housing and shifter are still in the car, SBF 306 motor. Eagle forged rotating assembly, trick flow aluminum heads, SVT Roller Rockers, head studs and...
  12. Windsor Engine Parts
    I bought a 351W and I am freshening it up with a 408 stroker kit. The following parts are for sale. Rotating assembly is balanced and only had 2K miles. Rebuilding it to go bigger and faster. 1-351W cast crankshaft turned 10-10 and ready to use, 351W stock rods with forged pistons (L2446)...
  13. 5.0/5.8 Engine Tech
    Hi guys! I'm sorta new at this so forgive me if i don't do this right....I just have a question. I have read someplace and often heard that the same piston in Ford 306 is the same piston used in a 351 to 393 stroker engine. Can anyone verify this. Thanks
  14. Windsor Engine Parts
    For sale: 306 rotating assembly, good condition with low miles. Forged L2482 +.030" flat top pistons cut for 2.05" valve, mounted on reconditioned stock rods with ARP bolts & factory crank. Car was sold, I'm parted out what is left. $200 obo + shipping. Paypal is OK & I'll eat the fees.
  15. 94/95 Tech
    Without REALLY getting into it I have built this car and after shopping around decided to go with moates/quarterhorse for my software data logger and they have been really helpful. And in typical form after we have screwed around with trying to get my factory ECU to take a tune :curses: we start...
  16. Windsor Engine Parts
    Set of 8 Wiseco forged aluminum pistons 4.030in with Eagle i-beam connecting rods 5.090in,. assembled. Never used, still in the original box. Im asking $750. pistons part #: pt012H3 rods part #: 5090FP
  17. 5.0/5.8 Engine Tech
    Hello, im starting a 306 build and i bought an explorer intake about a week ago on corral, then locally there was a guy selling a tubular with all the injectors and 75mm throttle body way too cheap for me to pass up! From what i understand the gt40 tubular, gt 40 explorer, and the cobra intakes...
  18. Windsor Engine Parts
    Hello, im looking for some forged 30 over pistons for use in a 306/302 based engine. preferably new but low mileage great condition is a possibility...if youve got some laying around and would rather have cash than stuff taking up room...money waiting 4.030 forged 306/302 pistons pm me or...
  19. 5.0/5.8 Engine Tech
    http://www.youtube.com/watch?v=IIAvON-cul8 motor started right away with no difficulties timing was a little off at the time of the video though. what you guys think??
  20. 5.0/5.8 Engine Tech
    OK EVERYONE I JUST STARTED UP MY CAR YESTERDAY AND MAN DOES SHE SOUND GOOD I WILL POST VIDS SOON. OK SO ITS A.... 306-STOCK CRANK N RODS, SPEED PRO FLAT TOP PISTONS. FRESH E-7 HEADS MILLED A BIT TRICK FLOW STAGE 1 WITH 1.7 ROCKERS RPM MANIFOLD AND 650 MIGHTY DEMON ALSO HAVE NEW DISTRIBUTER FROM...
1-20 of 37 Results
Top