Ford Mustang Forums banner

Search results

1-20 of 33 Results
Advanced Search
  1. ProM ECU Mount Option

    Pro-M EFI Systems
    In an effort to not drill into my floor pans under my seat, I came up with a way to mount the ECU using a Holley bracket that comes with their new Terminator X kits. It is a bracket made to mount the Holley ECU under a foxbody seat, I just modified it to use with the ProM ECU. It is held in...
  2. Innovate widebands :(

    Pro-M EFI Systems
    My Zeitronix ZT-4 kit came in today, looking forward to getting it installed my new ProM system very soon.
  3. WTB: 1990-1993 Dash Gauge Cluster Bezel

    Interior Parts
    I am looking for a good condition dash bezel for a 1990 foxbody, any 90-93 should work. (piece that goes around gauge cluster and houses light switch etc). PM me if you have something available.
  4. Kenne Bell Flowzilla

    Power Adders For Sale
    Is this one of the recent kits from TPS?
  5. Innovate DLG-1 Dual Wideband Kit - NEW *** SOLD ***

    Electronics and Entertainment
    SOLD !!
  6. Innovate DLG-1 Dual Wideband Kit - NEW *** SOLD ***

    Electronics and Entertainment
    I have a brand new Innovate DLG-1 kit for sale. This is a dual wideband kit with one single gauge for both widebands to display banks 1 and 2 at the same time. I will do $250 shipped to lower 48 states. * SOLD *
  7. Vortech V3 Si vs V1 Ti

    Superchargers
    Thanks for the input! I did end up going with a V3si with the Heritage series gears for that old school sound. I have a power pipe and do plan to eventually go with a 8" crank pulley, especially if I go 351w or 363. Very much looking forward to getting it installed either sometime this winter...
  8. Anderson Ford Powerpipe for Vortech Foxbody

    Power Adders For Sale
    PM sent
  9. LMR 10-Hole Wheels

    Wheels and Tires
    What intake are you running to get that under a stock hood? Very interested in doing something similar. And what else did you do to get it under the hood?
  10. Are all the sbf dart blocks made of the same steel?

    5.0/5.8 Engine Tech
    I imagine it would be a similar case as with offshore cylinder heads, by the time you spend money in machining to get it "right" you would have been better off going with a Dart to start with.
  11. Vortech V3 Si vs V1 Ti

    Superchargers
    600 to 700 HP would be plenty enough (at least I say that now). Then it will be the typical debate of 363 vs 357w when I decide to upgrade.
  12. Vortech V3 Si vs V1 Ti

    Superchargers
    I am heavily considering a V3 Si tuner kit (with Heritage series gears) while prices are good over the holidays. However, I am wondering if I should even consider a V1 Ti tuner kit? I have a stock bottom end 302 with TW 170 heads, Lunati 20350711 cam (221/229 @ .050 .540+ lift), TMOSS ported...
  13. What brand of injectors are you using?

    Pro-M EFI Systems
    Did you adjust your slopes any?
  14. Lowering/Spacing K-member - How much is too much?

    General Mustang Tech
    What did you have to do up front to account for that...it had to cause some suspension geometry issues?
  15. Can a cast crank take abuse or no (rpm )

    5.0/5.8 Engine Tech
    I agree, was basing on his cam choice and the fact he said GT40 heads "for now"
  16. Can a cast crank take abuse or no (rpm )

    5.0/5.8 Engine Tech
    A 347 at 7500 RPM in a stock block is a formula for disaster. 6000 RPM and below would be safer, but would depend on the power output and how well it is tuned.
  17. Anyone know where to get a motorcraft distributor pickup for '93 5.0?

    5.0/5.8 Engine Tech
    Try to find a NOS Motorcraft P/N DU-30-C They can be hard to find. There may be other brands that are OK but no experience with them
  18. What brand of injectors are you using?

    Pro-M EFI Systems
    Siemens Deka 80s here. No issues as is
  19. Lowering/Spacing K-member - How much is too much?

    General Mustang Tech
    In consideration of a possible 9.5 deck swap into my 1990 Mustang, how much can I space the k-member without causing issues? I have coil-overs up front so adjusting my ride height will be easy. I am trying to keep my stock hood and use an intake that won't choke a 408. I was considering using a...
  20. New 1986-1995 Kenne Bell 2.1

    Superchargers
    Has anyone else received their Kenne Bell and started their install yet? Very interested in the quality on this run. I expect it is very good?
1-20 of 33 Results
Top